manualshive.com logo in svg

Yamaha YFM700RSBH, Руководство пользователя

Поделиться
Скачать
Yamaha YFM700RSBH Скачать руководство пользователя страница 119

8-27

8

4. Install the gasket, tailpipe, and retainer and

align the bolt holes.

5. Install the bolts and tighten them to the spec-

ified torque.

6. Install the tailpipe cover and align the bolt

holes.

7. Install the bolts and tighten them to the spec-

ified torque.

WARNING

EWB02341

Do not start the engine when cleaning the
spark arrester, otherwise it could cause injury
to the eyes, burns, carbon monoxide poison-
ing, possibly leading to death, and start a fire.
Always let the exhaust system cool prior to
touching exhaust components.

 

EBU26812

Adjusting the engine idling speed

The engine idling speed must be checked and, if
necessary, adjusted as follows at the intervals
specified in the periodic maintenance and lubrica-
tion chart.

TIP

A diagnostic tachometer is needed to make this
adjustment.

 

1. Start the engine and warm it up.
2. Attach the tachometer to the spark plug lead.

1. Tailpipe
2. Spark arrester

Tightening torque:

Retainer bolt:

10 N·m (1.0 kgf·m, 7.2 lb·ft)

1

2

Tightening torque:

Tailpipe cover bolt:

8 N·m (0.8 kgf·m, 5.8 lb·ft)

U2LS62E0.book  Page 27  Thursday, February 25, 2016  8:44 AM

Содержание YFM700RSBH

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды