Yamaha YFM700RF Скачать руководство пользователя страница 61

Страница: 61 / 160

5-7

Tire information

This ATV is equipped with tubeless tires with
valves.

WARNING

EWB02552

Use of improper tires on this ATV may cause
loss of control, increasing your risk of an acci-
dent.

After extensive tests, only the tires listed below
have been approved for this model by Yamaha
Motor Manufacturing Corporation of America.

Aftermarket tires and rims

The tires and rims that came with your ATV were
designed to match the performance capabilities
and to provide the best combination of handling,
braking, and comfort. Other tires, rims, sizes, and
combinations may not be appropriate.

EBU19841

Chassis fasteners

Make sure that all nuts, bolts and screws are
properly tightened.

1. Tire wear limit

Front:

Manufacturer/model:

MAXXIS/MS13 Bias

Size:

AT22 x 7-10

Type:

Tubeless

Rear:

Manufacturer/model:

MAXXIS/M976Y Bias

Size:

AT20 x 10-9

Type:

Tubeless

U2LS60E0.book Page 7 Wednesday, June 18, 2014 11:12 AM

Содержание YFM700RF

































































































































































Результаты поиска

Содержание YFM700RF

Отзывы:

Бренды по названию

Популярные бренды

Yamaha YFM700RF, Руководство пользователя

Результаты поиска

Содержание YFM700RF

Отзывы:

Бренды по названию

Популярные бренды