Yamaha YFM700RF страница 121 Скачать руководство пользователя | Manualshive

Страница: 121 / 160

background image

8-29

8

4. Tighten the locknut.
5. Slide the rubber cover to its original position.

EBU24061

Valve clearance

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU24081

Adjusting the reverse lock release ca-
ble

The reverse lock release cable stretches with use,
which can result in improper function. Therefore,
the reverse lock release cable should be checked
and adjusted at the intervals specified in the peri-
odic maintenance and lubrication chart.

EBU29602

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be
performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

EBU24131

Checking the front and rear brake pads

The front and rear brake pads must be checked
for wear at the intervals specified in the periodic
maintenance and lubrication chart.

1. Rubber cover
2. Throttle lever free play adjusting bolt
3. Locknut
4. Throttle lever free play

3

2

4

(a)

(b)

1

U2LS60E0.book Page 29 Wednesday, June 18, 2014 11:12 AM

«
...
119
120
121
122
123
...
»

Содержание YFM700RF

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM700RF

GOOSENECK LIVESTOCK

Бренд: Wilson Trailer Страницы: 80

Бренд: Bosch Страницы: 2

Бренд: Aosom Страницы: 5

MAVERICK Sport MAX 1000R

Бренд: Can-Am Страницы: 187

Бренд: Logan Страницы: 28

amphibious, off-road utility vehicle

Бренд: Centaur Страницы: 56

Бренд: Polaris Страницы: 346

Бренд: KAYO MOTOR Страницы: 91

BurdenMaster B 2-00

Бренд: Taylor-Dunn Страницы: 266

YXZ 1000R SS 2022

Бренд: Yamaha Страницы: 216

Бренд: Opus Страницы: 21

Бренд: Baja motorsports Страницы: 44

UTV Desertcross 1000cc-3

Бренд: ODES Страницы: 230

Бренд: URBANGLIDE Страницы: 16

Бренд: Tuff stuff Страницы: 17

Бренд: Sauber Страницы: 8

2010 TXT 48 FLEET

Бренд: Ezgo Страницы: 50

Бренд: Ezgo Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды