Yamaha YFM35RX страница 98 Скачать руководство пользователя | Manualshive

Страница: 98 / 134

background image

8-20

8

described in the following section, however, may
be performed by the owner as part of routine main-
tenance.

CAUTION:

ECB00480

The carburetor has been set and extensively
tested at the Yamaha factory. Changing these
settings without sufficient technical knowl-
edge may result in poor performance of or
damage to the engine.

EBU24000

Adjusting the engine idling speed

The engine idling speed must be checked and, if
necessary, adjusted as follows at the intervals
specified in the periodic maintenance and lubrica-
tion chart.

NOTE:

A diagnostic tachometer is needed to make this
adjustment.

1. Start the engine and warm it up.

NOTE:

The engine is warm when it quickly responds to the
throttle.

2. Attach the tachometer to the spark plug lead.

3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-
crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

NOTE:

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5YT64E0.book Page 20 Monday, April 9, 2007 1:03 PM

«
...
96
97
98
99
100
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды