Yamaha YFM35RX Скачать руководство пользователя | Manualshive

Страница: 48 / 134

background image

6-3

6

NOTE:

The engine is warm when it responds normally to
the throttle with the starter (choke) turned off.

EBU20291

Starting a warm engine

Follow the same procedure as for starting a cold
engine, with the exception that the starter (choke)
is not required when the engine is warm. Instead,
start the engine with the throttle slightly open.

EBU20340

Operating the drive select lever and
driving in reverse

CAUTION:

ECB00170

Before shifting, stop the ATV, otherwise the
transmission may be damaged.

Shifting: Reverse to Forward

1. Bring the ATV to a complete stop.
2. Pull in the clutch lever to disengage the clutch.
3. Apply the brake pedal.
4. While pulling the drive select lever handle up-

ward, move the drive select lever forward until
it completely stops.

5. Release the brake pedal.
6. Open the throttle lever gradually and release

the clutch lever slowly.

Shifting: Forward to Reverse

1. Bring the ATV to a complete stop.
2. Pull in the clutch lever to disengage the clutch.
3. Apply the brake pedal.
4. While pulling the drive select lever handle up-

ward, move the drive select lever to the rear
until it completely stops.

1. Drive select lever
2. Drive select lever handle

3. For forward drive

4. For reverse drive

U5YT64E0.book Page 3 Monday, April 9, 2007 1:03 PM

«
...
46
47
48
49
50
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды