Yamaha YFM35RX Скачать руководство пользователя | Manualshive

Страница: 100 / 134

background image

8-22

8

EBU24130

Checking the front and rear brake pads

The front and rear brake pads must be checked for
wear at the intervals specified in the periodic main-
tenance and lubrication chart.

EBU28790

Front brake pads

Each brake pad is provided with two wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-
tor grooves. If a brake pad has worn to the point
that a wear indicator groove almost appears, have
a Yamaha dealer replace the brake pads as a set.

NOTE:

The wheels need to be removed to check the
brake pads. (See page 8-42.)

EBU28800

Rear brake pads

Each brake pad is provided with two wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-
tor grooves. If a brake pad has worn to the point
that a wear indicator groove almost appears, have
a Yamaha dealer replace the brake pads as a set.

1. Wear indicator groove

1. Wear indicator groove

U5YT64E0.book Page 22 Monday, April 9, 2007 1:03 PM

«
...
98
99
100
101
102
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды