Yamaha YFM350RB страница 95 Скачать руководство пользователя | Manualshive

Страница: 95 / 140

background image

8-15

8

NOTICE

ECB00300

●

In order to prevent clutch slippage (since the
engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of
a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV-
ING II” or higher.

●

Make sure that no foreign material enters the
crankcase.

13. Start the engine, and then let it idle for several

minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.

14. Turn the engine off, wait at least ten minutes,

and then check the oil level and correct it if
necessary.

EBU23743

Cleaning the air filter element

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.

TIP
There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-12.)
3. Remove the air filter case cover by unhooking

the holders.

1. Air filter case check hose

U1BS62E0.book Page 15 Monday, April 18, 2011 6:43 PM

«
...
93
94
95
96
97
...
»

Содержание YFM350RB













































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RB

Бренд: Yamaha Страницы: 390

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды