manualshive.com logo in svg

Yamaha YFM350RB, Руководство пользователя

Поделиться
Скачать
Yamaha YFM350RB Скачать руководство пользователя страница 51

6-4

6

reverse, make sure there are no people or ob-
stacles behind you. When it is safe to proceed,
go slowly.

1. Bring the ATV to a complete stop.
2. Pull in the clutch lever to disengage the clutch.
3. Apply the brake pedal.
4. While pulling the drive select lever handle up-

ward, move the drive select lever to the rear
until it completely stops.

TIP
When in reverse, the reverse indicator light should
be on. If the indicator light does not come on, have
a Yamaha dealer check the electrical circuit.

5. Check behind you for people or obstacles,

and then release the brake pedal.

6. Open the throttle lever gradually and release

the clutch lever slowly. Continue to watch to
the rear while backing.

EBU29762

Shifting 

This ATV has a 6-speed forward and 1-speed re-
verse transmission. The transmission allows you
to control the amount of power you have available
at a given speed or for starting, accelerating, climb-
ing hills, etc.
To shift into neutral, release the throttle lever, ap-
ply the clutch, and then repeatedly depress the
shift pedal until it stops.
When it stops, it will be in first gear. Raise the pedal
slightly to reach the neutral position, and then re-
lease the clutch.

1. Shift pedal

2. Neutral position

U1BS62E0.book  Page 4  Monday, April 18, 2011  6:43 PM

Содержание YFM350RB













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды