Yamaha YFM350RB Скачать руководство пользователя страница 27

Страница: 27 / 140

4-2

EBU17793

Indicator lights

EBU17860

Neutral indicator light “

”

This indicator light comes on when the transmis-
sion is in the neutral position.

EBU17830

Reverse indicator light “

”

This indicator light comes on when the transmis-
sion is in the reverse position.

EBU18061

Handlebar switches

EBU18080

Engine stop switch “

”

Set this switch to “

” before starting the engine.

The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “

”.

1. Reverse indicator light “R”

2. Neutral indicator light “N”

1. Light switch “

/OFF”

2. Engine stop switch “

”

3. Start switch “

”

U1BS62E0.book Page 2 Monday, April 18, 2011 6:43 PM

Содержание YFM350RB













































































































































Результаты поиска

Содержание YFM350RB

Отзывы:

Yamaha YFM350RB, Руководство пользователя, Страница: 27 / 140

Результаты поиска

Содержание YFM350RB

Отзывы: