Yamaha XT660R Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-24

6

●

Be careful that water does not en-
ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

●

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

●

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.

EAU22760

Drive chain slack

The drive chain slack should be
checked before each ride and adjusted
if necessary.

EAU22782

To check the drive chain slack

1. Place the motorcycle on the side-

stand.

NOTE:

When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.

2. Shift the transmission into the neu-

tral position.

3. Move the rear wheel by pushing

the motorcycle to locate the tight-
est portion of the drive chain, and
then measure the drive chain slack
as shown.

4. If the drive chain slack is incorrect,

adjust it as follows.

NOTE:

When checking the drive chain slack,
the chain tensioner should not be
touching the drive chain.

EAU22932

To adjust the drive chain slack
(XT660R)

1. Loosen the axle nut, then loosen

the locknut at each end of the
swingarm.

2. To tighten the drive chain, turn the

adjusting nut at each end of the
swingarm in direction (a). To loos-
en the drive chain, turn the adjust-
ing nut at each end of the
swingarm in direction (b), and then
push the rear wheel forward.

1. Drive chain slack

Drive chain slack:

40.0–55.0 mm (1.57–2.17 in)

U5VKE1E0.book Page 24 Tuesday, July 18, 2006 1:00 PM

«
...
60
61
62
63
64
...
»

Содержание XT660R





























































































Отзывы:

Нет отзывов

Похожие инструкции для XT660R

Бренд: Victory Motorcycles Страницы: 332

SBL.04.650.10000/B

Бренд: SW-Motech Страницы: 2

Бренд: Lakeland Страницы: 16

Бренд: B&G electronics Страницы: 5

Бренд: Termignoni Страницы: 9

Бренд: R&G Страницы: 6

Бренд: Touratech Страницы: 4

Бренд: Honda Страницы: 362

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 124

ROAD STAR XV16A

Бренд: Yamaha Страницы: 117

X MAX CZD300P 2022

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды