manualshive.com logo in svg

Yamaha XT250D, Руководство пользователя

Поделиться
Скачать
Yamaha XT250D Скачать руководство пользователя страница 86

10-1

1

2

3

4

5

6

7

8

9

10

CONSUMER INFORMATION

EAU26353

Identification numbers 

Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.

KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION 
NUMBER:

MODEL LABEL INFORMATION:

EAU26381

Key identification number 

The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.

EAU26400

Vehicle identification number 

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.

TIP

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in your
area.

1. Key identification number

1. Vehicle identification number

1

1YB-9-10.book  1 ページ  ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды