Yamaha XT250D Скачать руководство пользователя

Страница: 75 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-37

5. Remove the washer, spacers and

the wheel.

NOTICE:

Do not apply

the brake after the wheel has
been removed together with the
brake disc, otherwise the brake
pads will be forced shut.

[ECA11071]

EAU51611

To install the front wheel

1. Install the spacers into both sides

of the wheel hub.

2. Lift the wheel up between the fork

legs.

TIP

Make sure that there is enough space
between the brake pads before insert-
ing the brake disc into the caliper.

3. Insert the wheel axle (together with

the right side washer) from the
right-hand side.

4. Install the left side washer and the

axle nut.

5. Lower the front wheel so that it is

on the ground.

6. Tighten the axle nut to the speci-

fied torque.

7. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU51621

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.
2. Lift the rear wheel off the ground

according to the procedure on
page 7-36.

3. Turn the drive chain adjusting

plate on each side of the swingarm
fully in direction (a).

4. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

Tightening torque:

Axle nut:

85 Nm (8.5 m·kgf, 61 ft·lbf)

1YB-9-10.book 37 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды