Yamaha XT250D страница 74 Скачать руководство пользователя | Manualshive

Страница: 74 / 100

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-36

1

2

3

4

5

6

7

8

9

EAU24350

Supporting the motorcycle

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing
a jack either under each side of the

frame in front of the rear wheel or under
each side of the swingarm.

EAU24360

Front wheel

EAU51600

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.

2. Lift the front wheel off the ground

according to the procedure in the
previous section “Supporting the
motorcycle”.

3. Remove the axle nut and the

washer.

4. Pull the wheel axle out.

1. Axle nut

1

1YB-9-10.book 36 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
72
73
74
75
76
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Бренд: Yamaha Страницы: 568

Бренд: Honda Страницы: 28

Бренд: MOTO GUZZI Страницы: 209

Бренд: KTM Страницы: 36

Бренд: Honda Страницы: 127

Бренд: Blata Страницы: 17

Outlander 6x6 450 XU+ 2022

Бренд: Can-Am Страницы: 226

Бренд: DYNATEK Страницы: 12

Бренд: Brixton Страницы: 49

Бренд: RIEJU Страницы: 147

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 356

Бренд: Yamaha Страницы: 418

Бренд: Yamaha Страницы: 442

Бренд: Yamaha Страницы: 556

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды