manualshive.com logo in svg

Yamaha XT250D, Руководство пользователя

Поделиться
Скачать
Yamaha XT250D Скачать руководство пользователя страница 71

PERIODIC MAINTENANCE AND ADJUSTMENT

7-33

2

3

4

5

6

7

8

9

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU23816

Replacing the headlight bulb 

This model is equipped with a halogen
bulb headlight. If the headlight bulb
burns out, replace it as follows.

NOTICE

ECA10650

Take care not to damage the follow-
ing parts:

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

1. Remove cowling A. (See

page 7-9.)

2. Remove the headlight unit by re-

moving the bolts.

3. Disconnect the headlight coupler,

and then remove the headlight

Specified fuses:

Main fuse: 

30.0 A

Signaling system fuse: 

10.0 A

Ignition fuse: 

10.0 A

Headlight fuse: 

15.0 A

Fuel injection system fuse: 

10.0 A

1. Do not touch the glass part of the bulb.

1. Bolt

1

1YB-9-10.book  33 ページ  ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды