manualshive.com logo in svg

Yamaha XT250D, Руководство пользователя

Поделиться
Скачать
Yamaha XT250D Скачать руководство пользователя страница 70

PERIODIC MAINTENANCE AND ADJUSTMENT

7-32

1

2

3

4

5

6

7

8

9

stallation. 

NOTICE:

 When install-

ing the battery, be sure the key
is turned to “OFF”, then con-
nect the positive lead before
connecting the negative
lead.

[ECA16840]

 

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU53900

Replacing the fuses 

The main fuse and the fuse boxes,
which contains the fuses for the individ-
ual circuits, are located behind panel C.
(See page 7-9.)

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage. 

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

 

1. Fuse box 1

2. Fuse box 2

3. Main fuse

4. Spare main fuse

3

4

2

1

1. Spare fuse

2. Ignition fuse

3. Fuel injection system fuse

4. Spare fuse

5. Headlight fuse

6. Signaling system fuse

1

2 3

4

5

6

1YB-9-10.book  32 ページ  ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды