Yamaha XT250D страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 100

background image

OPERATION AND IMPORTANT RIDING POINTS

6-2

1

2

3

4

5

6

7

8

9

light should come on. If not, ask a
Yamaha dealer to check the elec-
trical circuit.

3. Start the engine by pushing the

start switch.
If the engine fails to start, release
the start switch, wait a few sec-
onds, and then try again. Each
starting attempt should be as short
as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one at-
tempt.

NOTICE

ECA11042

For maximum engine life, never ac-
celerate hard when the engine is
cold!

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

TIP

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

NOTICE

ECA10260



Even with the transmission in

the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.



Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16681

To start out and accelerate

1. Pull the clutch lever to disengage

the clutch.

2. Shift the transmission into first

gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at

the same time, release the clutch
lever slowly.

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,

1. Neutral position

2. Shift pedal

2

1

2

3

4

5

N

1

1YB-9-10.book 2 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
34
35
36
37
38
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Бренд: Palm Страницы: 14

Бренд: Miller Страницы: 12

Бренд: PIAGGIO Страницы: 8

Бренд: TVS Страницы: 48

Бренд: DYNATEK Страницы: 4

Бренд: Happy Trails Страницы: 2

Бренд: Malaguti Страницы: 272

Бренд: IBEX Страницы: 2

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 22

Бренд: R&G Страницы: 20

Бренд: R&G Страницы: 24

Бренд: R&G Страницы: 24

Бренд: R&G Страницы: 27

Бренд: R&G Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды