Yamaha XT250D Скачать руководство пользователя

Страница: 26 / 100

INSTRUMENT AND CONTROL FUNCTIONS

4-7

EAU12891

Brake lever

The brake lever is located on the right
side of the handlebar. To apply the front
brake, pull the lever toward the throttle
grip.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAUM1793

Fuel tank cap

To remove the fuel tank cap

1. Open the fuel tank cap lock cover.
2. Insert the key into the lock and turn

it 1/4 turn clockwise. The lock will
be released and the fuel tank cap
can be removed.

To install the fuel tank cap

1. Push and install the fuel tank cap

into position with the key inserted
in the lock.

2. Turn the key counterclockwise to

the original position, and then re-
move it.

1. Brake lever

1. Brake pedal

1. Fuel tank cap lock cover

2. Unlock.

1YB-9-10.book 7 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды