background image

 

2   

 

XP7000/XP5000/XP3500/XP2500/XP1000 Owner’s Manual

 

The above warning is located on the top of the unit.

 

Explanation of Graphical Symbols

 

The lightning flash with arrowhead symbol 
within an equilateral triangle is intended to alert 
the user to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude to 
constitute a risk of electric shock to persons.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the product.

 

IMPORTANT SAFETY INSTRUCTIONS

 

1

Read these instructions.

2

Keep these instructions.

3

Heed all warnings.

4

Follow all instructions.

5

Do not use this apparatus near water.

6

Clean only with dry cloth.

7

Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.

8

Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.

9

Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades 
with one wider than the other. A grounding type plug 
has two blades and a third grounding prong. The wide 
blade or the third prong are provided for your safety. If 
the provided plug does not fit into your outlet, consult 
an electrician for replacement of the obsolete outlet.

10

Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.

11

Only use attachments/accessories specified by the 
manufacturer.

12

Use only with the cart, stand, 
tripod, bracket, or table specified 
by the manufacturer, or sold with 
the apparatus. When a cart is 
used, use caution when moving 
the cart/apparatus combination 
to avoid injury from tip-over.

13

Unplug this apparatus during 
lightning storms or when unused for long periods of 
time.

14

Refer all servicing to qualified service personnel. 
Servicing is required when the apparatus has been 
damaged in any way, such as power-supply cord or plug 
is damaged, liquid has been spilled or objects have 
fallen into the apparatus, the apparatus has been 
exposed to rain or moisture, does not operate normally, 
or has been dropped.

 

(98-6500)

CAUTION: TO REDUCE THE RISK OF 

ELECTRIC SHOCK, DO NOT REMOVE 

COVER (OR BACK). NO USER-SERVICEABLE 

PARTS INSIDE. REFER SERVICING TO 

QUALIFIED SERVICE PERSONNEL.

C A U T I O N

RISK OF ELECTRIC SHOCK

DO NOT OPEN

 

WARNING

 

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

 

FCC INFORMATION (U.S.A.)

 

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

 

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not 
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

 

2. IMPORTANT:

 

 When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s 

supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authori-
zation to use this product in the USA.

 

* This applies only to products (XP7000, XP5000) distributed by YAMAHA CORPORATION OF AMERICA.

(oscillator)

Содержание XP1000























Отзывы: