manualshive.com logo in svg

Yamaha WR250X, Руководство пользователя

Поделиться
Скачать
Yamaha WR250X Скачать руководство пользователя страница 66

PERIODIC MAINTENANCE AND ADJUSTMENT

7-21

7

EAU45322

Adjusting the engine idling 
speed 

The engine idling speed must be
checked and, if necessary, adjusted as
follows.

TIP

A digital tachometer is needed to make
this adjustment.

1. Position the digital tachometer at

the ignition coil, which is located in
the spark plug cap.

2. Check the engine idling speed

and, if necessary, adjust it to spec-
ification by turning the idle adjust-
ing screw. To increase the engine
idling speed, turn the screw in di-
rection (a). To decrease the en-
gine idling speed, turn the screw in
direction (b).

TIP

If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.

EAU21382

Checking the throttle cable 
free play 

The throttle cable free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

1. Idle adjusting screw

Engine idling speed:

1450–1650 r/min

1

(b)

(a)

1. Throttle cable free play

1

U32C15E0.book  Page 21  Tuesday, July 14, 2009  11:43 AM

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды