Yamaha WR250F 2022 Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 404

background image

FUEL TANK

7-2

EAM30263

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank cap with a pump.

2. Remove:

•

Fuel hose coupler

WARNING

EWA19370

Cover the fuel hose connection with a cloth

when disconnecting it. This is because re-

sidual pressure in the fuel hose could cause

fuel to spurt out when the hose is removed.

NOTICE

ECA26520

• Make sure that the fuel hose is disconnect-

ed by hand. Do not forcefully disconnect

the hose with tools.

• When removing the fuel tank, handle it

carefully. If the discharge port of the fuel

pump touches the ground or other objects,

the discharge port could be damaged.

TIP

•

To disconnect the fuel hose from the fuel tank,
remove the fuel hose connector holder “a”, and
then slide the fuel hose connector cover.

•

To remove the fuel hose from the fuel rail, slide
the fuel hose connector cover “1” on the end of
the hose in the direction of the arrow shown,
press the two buttons “2” on the sides of the
connector, and then remove the hose.

•

Before removing the hose, place a few cloths
in the area under where it will be removed.

•

To prevent sand, dust, and other foreign mate-
rials from entering the fuel pump, install the in-
cluded fuel hose joint cover 1 “3” and the fuel
hose joint cover 2 “4” onto the disconnected
fuel hose and the fuel pump.

3. Remove:

•

Side cover (left/right)

•

Seat

•

Air scoop (left/right)

•

Fuel tank

TIP

Do not set the fuel tank down on the installation
surface of the fuel pump. Be sure to lean the fuel
tank against a wall or the like.

EAM30264

REMOVING THE FUEL PUMP

1. Remove:

•

Fuel pump

NOTICE

ECA24720

Do not drop the fuel pump or give it a strong

shock.

EAM30265

CHECKING THE FUEL PUMP BODY

1. Check:

•

Fuel pump body
Obstructions



Clean.

Cracks/damage



Replace the fuel pump

assembly.

EAM30508

CHECKING THE FUEL PUMP OPERATION

1. Check:

•

Fuel pump operation
Refer to “CHECKING THE FUEL PRES-
SURE” on page 7-7.

a

1

2

3

4

«
...
289
290
291
292
293
...
»

Содержание WR250F 2022





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250F 2022

Бренд: Tao Motor Страницы: 3

Бренд: Yoshimura Страницы: 7

Бренд: J&M Страницы: 5

65175810022-00-40

Бренд: hepco & becker Страницы: 4

Бренд: KSR Moto Страницы: 51

Бренд: PIAGGIO Страницы: 8

Бренд: Miller Страницы: 22

Бренд: Yamaha Страницы: 110

Бренд: DYNATEK Страницы: 4

1003007FONTANASPRINT

Бренд: DYNATEK Страницы: 7

Бренд: DYNATEK Страницы: 12

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 84

Бренд: JAWA Страницы: 22

Бренд: Shad Страницы: 2

Super Meteor 650

Бренд: Royal Enfield Страницы: 124

BOOMERANG 7554CB

Бренд: Bagster Страницы: 2

Бренд: Yamaha Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды