Yamaha WR250F 2022 Скачать руководство пользователя страница 171

Страница: 171 / 404

FRONT FORK

4-45

EAM30055

REMOVING THE FRONT FORK LEGS

1. Use a maintenance stand to raise the front

wheel off the ground.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Record the adjusting screw setting position be-
fore loosening the adjuster and the base valve.

2. Loosen:

•

Upper bracket pinch bolt

•

Damper assembly

•

Lower bracket pinch bolt

WARNING

EWA20350

Before loosening the upper and lower brack-

et pinch bolts, support the front fork leg.

TIP

Before removing the front fork leg from the vehi-
cle, loosen the damper assembly “1” with the
cap bolt ring wrench “2”.

3. Remove:

•

Front fork leg

EAM30056

DISASSEMBLING THE FRONT FORK LEGS

1. Drain:

•

Fork oil

2. Remove:

•

Adjuster “1”
(from the inner tube)

TIP

•

While compressing the inner tube “2”, set the
cap bolt ring wrench “4” between the inner tube
and locknut “3”.

•

Hold the locknut and remove the adjuster.

NOTICE

ECA24520

Do not remove the locknut as the damper rod

may go into the damper assembly and not be

taken out.

3. Remove:

•

Dust seal “1”

•

Stopper ring “2”
(with a flat-head screwdriver)

NOTICE

ECA14180

Do not scratch the inner tube.

4. Remove:

•

Inner tube “1”
a. Push in slowly “a” the inner tube just be-

fore it bottoms out and then pull it back
quickly “b”.

b. Repeat this step until the inner tube can be

pulled out from the outer tube.

Cap bolt ring wrench

90890-01501

Cap bolt ring wrench

YM-01501

Cap bolt ring wrench

90890-01501

Cap bolt ring wrench

YM-01501

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды