Yamaha WR250F 2022 Скачать руководство пользователя страница 122

Страница: 122 / 404

CHASSIS

3-34

EAM30253

CHECKING THE CHASSIS FASTENERS

Make sure that all nuts, bolts, and screws are
properly tightened.
Refer to “CHASSIS TIGHTENING TORQUES”
on page 2-14.

EAM30248

CHECKING AND LUBRICATING THE

CABLES

The following procedure applies to all of the in-
ner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable to

corrode and interfere with its movement. Re-

place damaged outer cable and inner cables

as soon as possible.

1. Check:

•

Outer cable
Damage



Replace.

2. Check:

•

Cable operation
Rough movement



Lubricate.

TIP

Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.

EAM30483

LUBRICATING THE BRAKE LEVER

1. Lubricate the pivoting points and metal-to-

metal moving parts of the following parts.

•

Brake lever

EAM30503

LUBRICATING THE CLUTCH LEVER

1. Lubricate the pivoting points and metal-to-

metal moving parts of the following parts.

•

Clutch lever

EAM30250

LUBRICATING THE PEDAL

1. Lubricate the pivoting point and metal-to-met-

al moving parts of the pedal.

EAM30504

CHECKING THE SIDESTAND

1. Check:

•

Sidestand operation
Check that the sidestand moves smoothly.
Rough movement



Repair or replace.

EAM30252

LUBRICATING THE SIDESTAND

Lubricate the pivoting point and metal-to-metal
moving parts of the sidestand.

Recommended lubricant

Engine oil or a suitable cable lu-

bricant

Recommended lubricant

Silicone grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды