Yamaha WaveRunner VXS 2015 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 108

Yamaha WaveRunner VXS 2015 Скачать руководство пользователя страница 7

General and important labels

1

EJU36452

Identification numbers

Record the Primary Identification (PRI-ID)
number, Craft Identification Number (CIN),
and engine serial number in the spaces pro-
vided for assistance when ordering spare
parts from a Yamaha dealer. Also record and
keep these ID numbers in a separate place in
case your watercraft is stolen.

EJU42521

Primary Identification (PRI-ID) number

The PRI-ID number is stamped on a plate at-
tached inside the engine compartment. (See
page 43 for seat removal and installation pro-
cedures and page 48 for information on the
removable watertight storage compartment.)

MODEL:

VX1800-P (VXS)
VX1800A-P (VXR)

EJU36551

Craft Identification Number (CIN)

The CIN is stamped on a plate attached to
the aft deck.

EJU30312

Engine serial number

The engine serial number is stamped on a
plate attached to the engine unit. (See page
43 for seat removal and installation proce-
dures.)

1

Primary Identification (PRI-ID) number loca-
tion

1

MODEL

F2W

F

PRI-I.D.

YAMAHA MOTOR CO., LTD.
ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE
COMPONENTS.
ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICAINES ET
JAPONAISES.

2 W

1

Craft Identification Number (CIN) location

1

Engine serial number location

1

1

UF2W70E0.book Page 1 Tuesday, December 8, 2015 9:03 AM

«
...
5
6
7
8
9
...
»

Содержание WaveRunner VXS 2015













































































































Отзывы:

Нет отзывов