Yamaha WaveRunner VXS 2015 Скачать руководство пользователя | Manualshive

Страница: 43 / 108

background image

Instrument operation

37

EJU43760

Multifunction information

center

The multifunction information center displays
various watercraft information.

Multifunction information center initial op-
eration

When the multifunction information center is
activated, all of the display segments come
on. After 2 seconds, the warning indicators in
the information display go off, and then the
center starts to operate normally.
If only the multifunction information center is
activated, the “WARNING” indicator light
blinks once.

TIP:

The “UNLOCK” indicator light also comes on
as part of the initial operation.
The “UNLOCK” indicator light will go off
when the engine is started.

Multifunction information center standby
state

If the multifunction information center does
not receive any operation input within 25 sec-
onds after the engine stops, the center will
turn off and enter a standby state. When the
engine is started again, the displays return to

their state before the center turned off, and
then the center starts to operate normally.

EJU35027

Information display

The information display shows watercraft op-
erating conditions.

EJU43830

Speedometer

The speedometer shows the watercraft
speed against water.
By switching the display units, the speed can
be shown in kilometers per hour “km/h” or
miles per hour “MPH”.

1

“UNLOCK” indicator light

2

Information display

3

“L-MODE” indicator light

4

“WARNING” indicator light

1

2

3

4

1

Trim indicator

2

Tachometer

3

Speedometer

4

Oil pressure warning indicator

5

Engine overheat warning indicator

6

Check engine warning indicator

7

Shift indicator

8

Fuel indicator

9

Fuel level meter

2

1

3

4 5 6

8

7

9

UF2W70E0.book Page 37 Tuesday, December 8, 2015 9:03 AM

«
...
41
42
43
44
45
...
»

Содержание WaveRunner VXS 2015













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VXS 2015

Бренд: Nacra Страницы: 40

Бренд: Grand Страницы: 17

Бренд: MasterCraft Страницы: 41

Бренд: Corsiva Yachting Страницы: 33

Бренд: Corsiva Yachting Страницы: 37

Bombardier GSX Limited 5625

Бренд: Sea-doo Страницы: 56

Бренд: VBOATS Страницы: 72

Бренд: Sea-doo Страницы: 130

Бренд: Sea-doo Страницы: 130

2014 Spark Series

Бренд: Sea-doo Страницы: 148

230 Challenger 2008

Бренд: Sea-doo Страницы: 160

Бренд: SAPHIRE BOATS Страницы: 74

Бренд: LaserPerformance Страницы: 11

Бренд: RIOT Страницы: 7

Бренд: SEALVER Страницы: 16

Бренд: Hanse Страницы: 20

Бренд: Performance Cruising Страницы: 59

Бренд: Gumotex Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды