Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 88

Страница: 88 / 98

Trouble recovery

EJU34562

Troubleshooting

If you have any trouble with your watercraft, use the troubleshooting chart to check for the
possible cause.
If you cannot find the cause, consult a Yamaha dealer.

EJU34596

Troubleshooting chart

Confirm the possible cause and remedy, and then refer to the applicable page.

TROUBLE

POSSIBLE CAUSE

REMEDY

PAGE

Engine does not
start (Starter motor
does not turn over)

Yamaha Se-
curity System
(VX Deluxe /
VX Cruiser)

Lock mode selected

Select unlock mode

Engine shut-
off switch

Clip not in place

Install clip

Fuse

Burned out

Replace fuse and
check wiring

Battery

Run down

Recharge

Poor terminal con-
nections

Tighten as required

Terminal corroded

Clean or replace

Starter motor

Faulty

Have serviced by
Yamaha dealer

—

Engine does not
start (Starter motor
turns over)

Throttle lever

Squeezed

Release

Fuel

Empty

Refill as soon as pos-
sible

Stale or contaminat-
ed

Have serviced by
Yamaha dealer

—

Fuel tank

Water or dirt present

Have serviced by
Yamaha dealer

—

Spark plug

Fouled or defective

Have serviced by
Yamaha dealer

—

Spark plug
cap

Not connected or
loose

Have serviced by
Yamaha dealer

—

Connected to wrong
cylinder

Have serviced by
Yamaha dealer

—

Fuel injec-
tion system

Fuel pump faulty

Have serviced by
Yamaha dealer

—

UF2P71E0.book Page 82 Wednesday, July 10, 2013 5:37 PM

Содержание WaveRunner VX Sport 2014



































































































Результаты поиска

Содержание WaveRunner VX Sport 2014

Отзывы:

Yamaha WaveRunner VX Sport 2014, Руководство владельца/оператора, Страница: 88 / 98

Результаты поиска

Содержание WaveRunner VX Sport 2014

Отзывы: