Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 98

Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 68

Operation

62

throttle lever is in the fully closed (idle) posi-
tion.

VX Deluxe / VX Cruiser:

When the shift lever is in the forward position
and the engine is running, the watercraft will
move forward. The watercraft will move for-
ward at trolling speed even if the throttle lever
is in the fully closed (idle) position. (See page

30 for information on operating the shift le-
ver.)

EJU33255

Turning the watercraft

WARNING

EWJ00772



Do not release the throttle lever when
trying to steer away from objects—you
need throttle to steer. A collision could
result in severe injury or death.



When operating at higher speeds, make
gradual turns or slow down before turn-
ing. Sharp high-speed turns may cause
the watercraft to slide sideways or spin,
throwing the operator and passenger(s)
overboard, which could cause an injury.

Steering control depends on the combination
of handlebar position and the amount of
throttle.

1

Shift lever

2

Forward position

1

2

UF2P71E0.book Page 62 Wednesday, July 10, 2013 5:37 PM

«
...
66
67
68
69
70
...
»

Содержание WaveRunner VX Sport 2014



































































































Отзывы:

Нет отзывов