Yamaha WaveRunner VX Deluxe 2007 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 96

Yamaha WaveRunner VX Deluxe 2007 Скачать руководство пользователя страница 64

Operation

57

(2) Board the watercraft from the side or the

rear.

(3) Attach the engine shut-off cord to your left

wrist, and then attach the clip to the en-
gine shut-off switch.

(4) Grip the handlebars with both hands,

place both feet on the floor of the footwell,
start the engine, and then look in all direc-
tions before starting off.

EJU33110

Boarding and starting from a dock

(1) Board the watercraft from the side.
(2) Attach the engine shut-off cord to your left

wrist, and then attach the clip to the en-
gine shut-off switch.

(3) Push the watercraft away from the dock,

grip the handlebars with both hands,
place both feet on the floor of the footwell,
start the engine, and then look in all direc-
tions before starting off.

EJU36080

Boarding and starting in deep water

WARNING

EWJ01110

●

The operator and passengers should
practice boarding in shallow water be-
fore riding in deep water. Boarding in
deep water requires more skill.

●

The fatigue and exposure that could re-
sult after unsuccessful attempts to get
back on the watercraft may increase the
risk of injuries and drowning.

EJU33140

Boarding alone

(1) Swim to the rear of the watercraft and

place both hands on the boarding plat-
form, pull yourself up, and then grasp the
handgrip with one hand.

(2) Pull yourself up to a kneeling position on

the platform, and then move to the seat
and sit astride.

(3) Attach the engine shut-off cord to your left

wrist, and then attach the clip to the en-
gine shut-off switch.

(4) Grip the handlebars with both hands,

place both feet on the floor of the footwell,

UF1K72E0.book Page 57 Wednesday, August 2, 2006 10:43 AM

«
...
62
63
64
65
66
...
»

Содержание WaveRunner VX Deluxe 2007

































































































Отзывы:

Нет отзывов