Yamaha WaveRunner VX Deluxe 2007 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 96

background image

Operation

50

may have collected around the jet in-
take.

EJU32660

Engine shut-off cord

Check that the engine shut-off cord is not
frayed or broken. If the cord is damaged, re-
place it; never try to repair it or tie it together.

EJU32670

Switches

CAUTION:

ECJ00410

Do not run the engine for more than 15
seconds when checking the switches on
land without supplying water, otherwise
the engine could overheat.

Check the start switch, the engine stop
switch, and the engine shut-off switch for
proper operation.
Push the start switch to start the engine. As
soon as the engine starts running, push the
engine stop switch to verify that the engine
stops immediately. Restart the engine, and
then pull the engine shut-off cord to remove
the clip from the engine shut-off switch to ver-
ify that the engine stops immediately. (See
pages 28 to 29 for information on proper op-
eration of the start switch, the engine stop
switch, and the engine shut-off switch.)

EJU32680

Cooling water pilot outlet

Check that water comes out from the cooling
water pilot outlet while the engine is running

1

Start switch

2

Engine stop switch

3

Engine shut-off switch

4

Clip

5

Engine shut-off cord

UF1K72E0.book Page 50 Wednesday, August 2, 2006 10:43 AM

«
...
55
56
57
58
59
...
»

Содержание WaveRunner VX Deluxe 2007

































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX Deluxe 2007

Sport Boat Models

Бренд: LARSON Страницы: 102

Бренд: Grand Страницы: 17

2950 Walkaround

Бренд: Pro-Line Boats Страницы: 42

Бренд: Sailfish Страницы: 41

Бренд: Edgewater Networks Страницы: 395

Бренд: Elan Страницы: 69

Бренд: Lifetime Страницы: 16

Бренд: Supra Страницы: 92

Бренд: Supra Страницы: 88

Hewes Redfisher 16

Бренд: Maverick Boat Страницы: 23

Бренд: Mercury Страницы: 88

Бренд: Bavaria Страницы: 77

Бренд: Pelican Страницы: 12

Бренд: Galaxy Страницы: 24

Бренд: Sailfish Страницы: 44

MERRY FISHER 855 OFF SHORE

Бренд: Jeanneau Страницы: 108

GP1300R WaveRunner 2006

Бренд: Yamaha Страницы: 126

Бренд: Fassmer Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды