Yamaha WaveRunner VX Cruiser 2007 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 96

Yamaha WaveRunner VX Cruiser 2007 Скачать руководство пользователя страница 72

Operation

65

EJU33451

Transporting

When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern eyes.

CAUTION:

ECJ00621

●

Do not attach ropes or tie downs to any
part of the watercraft other than the bow
eye and stern eyes to secure the water-
craft to the trailer. Otherwise, the water-
craft may be damaged.

●

Do not route ropes or tie downs over the
seat, as they may leave permanent
marks on the seat’s surface. Also, wrap
the ropes or tie downs with towels or
rags where they touch the body of the
watercraft to avoid scratches or dam-
age.

●

For VX Deluxe/VX Cruiser:
Before putting the watercraft on the trail-
er or transporting it, be sure to put the
shift lever in the forward position, other-
wise the reverse gate may hit an obsta-
cle, which may cause damage.

UF1K72E0.book Page 65 Wednesday, August 2, 2006 10:43 AM

«
...
70
71
72
73
74
...
»

Содержание WaveRunner VX Cruiser 2007

































































































Отзывы:

Нет отзывов