Yamaha WaveRunner VX 2018 страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 108

background image

Watercraft operation

33

TIP:

If the RiDE lever is squeezed while the throttle
lever is squeezed, the watercraft will slow
down, and once stopped, move in reverse.
To shift into neutral from forward:
(1) Release the throttle lever.
(2) Lightly squeeze and release the RiDE le-

ver. The “N” (neutral) shift indicator will
be displayed.

TIP:

If the RiDE lever is squeezed continuously,
the reverse gate will move to the reverse po-
sition.

EJU40001

Watercraft operation modes

EJU43820

Low RPM Mode (VX Deluxe /
VX Cruiser / VX Limited)

The Low RPM Mode is a function that limits
the maximum engine speed to approximately
90% of the maximum engine speed in the
normal mode.
The Low RPM Mode can only be activated
and deactivated by operating the remote
control transmitter that is included with this
watercraft. (See page 25 for information on
the remote control transmitter.)

TIP:

The Low RPM Mode can only be activated
when the engine is stopped in the unlock
mode of the Yamaha Security System.

Activating and deactivating the Low RPM
Mode

Activation of the Low RPM Mode will be con-
firmed by the number of beeps when the re-
mote control transmitter is operated, and by
the “L-MODE” indicator light of the multifunc-
tion information center. (See page 38 for in-
formation on the multifunction information
center.)

1

“N” (Neutral position)

1

1

Remote control transmitter

UF4G72E0.book Page 33 Tuesday, August 1, 2017 11:30 AM

«
...
37
38
39
40
41
...
»

Содержание WaveRunner VX 2018













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX 2018

Бренд: Feathercraft Страницы: 29

56 Side Console

Бренд: YAMARIN Страницы: 37

Бренд: Pro-Line Boats Страницы: 33

FLEXIBLE FURLER 2

Бренд: CDI Страницы: 18

13' Super Sport

Бренд: Boston Whaler Страницы: 24

Бренд: Boston Whaler Страницы: 88

150 Super Sport

Бренд: Boston Whaler Страницы: 82

Бренд: Mercury Страницы: 94

Бренд: Four winns Страницы: 79

Бренд: Bavaria Страницы: 26

Бренд: Lagoon Страницы: 80

2-IN-1 SLIDE & BOUNCE COMBO PARK

Бренд: Banzai Страницы: 8

Бренд: Yamaha Страницы: 134

Бренд: Arey's Pond Страницы: 10

Бренд: Wellcraft Страницы: 92

Бренд: West Marine Страницы: 20

1989 Tiara 2000

Бренд: PURSUIT Страницы: 29

1989 2200 Cuddy Outboard

Бренд: PURSUIT Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды