Yamaha WaveRunner VX 2015 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 108

Yamaha WaveRunner VX 2015 Скачать руководство пользователя страница 53

Equipment operation

47

could fall, which could result in severe in-
jury.

[EWJ01511]

EJU35147

Storage compartments

This watercraft is equipped with the following
storage compartments.
Only the securely closed watertight storage
compartment is waterproof. If you carry ob-
jects that must be kept dry, put them in a wa-
terproof bag.
Make sure that the storage compartments
are closed securely before operating the wa-
tercraft.

EJU43770

Bow storage compartment

The bow storage compartment is located un-
der the hood.

To open the bow storage compartment:
Pull the hood latch up, and then lift up the
rear of the hood.

1

Cleat

1

1

Hood latch

1

Bow storage compartment

Bow storage compartment:

Capacity:

72.0 L (19.0 US gal, 15.8 Imp.gal)

Load limit:

5.0 kg (11 lb)

1

1

1

UF2X70E0.book Page 47 Wednesday, September 17, 2014 8:52 AM

«
...
51
52
53
54
55
...
»

Содержание WaveRunner VX 2015













































































































Отзывы:

Нет отзывов