Yamaha VX Sport Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 106

Yamaha VX Sport Скачать руководство пользователя страница 64

Pre-operation checks

59

the dipstick attached to the oil tank filler cap.
(See page 51 for information on checking the
engine oil level.)

EJU32455

Bilge water check

Make sure that no bilge water has collected in
the engine compartment. If bilge water has
collected in the engine compartment, drain it.
(See page 53 for information on draining the
bilge water.)

EJU32484

Battery checks

Make sure that the battery terminals and
breather hose are not damaged and that the
battery leads and breather hose are connect-
ed properly.

WARNING! Fire or explosion

could result if the breather hose is dam-

aged, obstructed, or not connected prop-
erly.

[EWJ00451]

Make sure that the electrolyte level is be-
tween the minimum and maximum level
marks.

WARNING! Never operate the wa-

tercraft if the battery does not have suffi-
cient power to start the engine or if it
shows any other signs of decreased pow-
er. Loss of battery power may leave you
stranded.

[EWJ01240]

Make sure that the battery is securely held in
place.

EJU32613

Steering system checks

Turn the handlebars to the right and left sev-
eral times to make sure that operation is
smooth and unrestricted throughout the

1

Oil tank filler cap/Dipstick

1

Dipstick

2

Maximum level mark

3

Minimum level mark

1

2

1

3

1

Negative (–) battery terminal: Black lead

2

Positive (+) battery terminal: Red lead

3

Breather hose

1

Maximum level mark

2

Minimum level mark

1

2

3

UF2N10E0.book Page 59 Tuesday, October 6, 2009 5:02 PM

«
...
62
63
64
65
66
...
»

Содержание VX Sport











































































































Отзывы:

Нет отзывов