Yamaha VX Sport Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 106

Yamaha VX Sport Скачать руководство пользователя страница 30

Description

25

EJU40302

Watercraft glossary

Trolling speed

“Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The watercraft
is down in the water, and there is no wake.

Sub-planing speed

“Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water sur-
face, but you are still traveling through the water. There is a wake.

Planing speed

“Planing” is a faster speed. The watercraft is more level and is skimming on top of the water.
There is a wake.

Bow

The front end of the watercraft.

Stern

The rear end of the watercraft.

Starboard

The right side of the watercraft when facing forward.

Port

The left side of the watercraft when facing forward.

Bilge water

Water that has collected in the engine compartment.

Yamaha Engine Management System (YEMS)

YEMS is an integrated, computerized management system that controls and adjusts ignition
timing, fuel injection, engine diagnostics, and the off-throttle steering (OTS) system.

UF2N10E0.book Page 25 Tuesday, October 6, 2009 5:02 PM

«
...
28
29
30
31
32
...
»

Содержание VX Sport











































































































Отзывы:

Нет отзывов