manualshive.com logo in svg

Yamaha Viking YXM70VPHH 2016, Руководство пользователя

Поделиться
Скачать
Yamaha Viking YXM70VPHH 2016 Скачать руководство пользователя страница 146

8-47

8

4. Connect the negative lead of the jumper

cable to the negative terminal of the
charged battery and the other end of the
negative lead to an unpainted metal sur-
face of the frame of the vehicle to be
started.

5. Start the engine. (Refer to “Starting the

engine” on page 6-2.)

6. After the engine starts, disconnect the

negative lead of the jumper cable from
the frame and charged battery, and then

disconnect the positive lead of the jump-
er cable from the charged battery and the
battery in the vehicle.

7. Install the hood.

EBU33100

Fuse replacement

The main fuse, the fuel injection system fuse,
the EPS fuse, and the fuse box are located
under the hood. (See page 8-10 for hood re-
moval and installation procedures.)

1. Jumper cable negative lead

1

UB427BE0.book  Page 47  Friday, February 5, 2016  2:14 PM

Содержание Viking YXM70VPHH 2016













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды