manualshive.com logo in svg

Yamaha Viking YXM70VPHH 2016, Руководство пользователя

Поделиться
Скачать
Yamaha Viking YXM70VPHH 2016 Скачать руководство пользователя страница 132

8-33

8

EBU32460

Valve clearance

The correct valve clearance changes with
use, resulting in improper fuel/air supply or
engine noise. To prevent this, the valve clear-
ance must be adjusted regularly. This adjust-
ment  however,  should  be  left  to  a
professional Yamaha service technician.

EBU32470

Brakes

Replacement of brake components requires
professional knowledge. Brake service
should be performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or ad-
justed brakes could lead to a loss in brak-
ing ability and an accident.

 

EBU32480

Checking the front and rear brake pads

Each brake pad is provided with wear indica-
tor grooves, which allow you to check the
brake pad wear without having to disassem-
ble the brake. To check the brake pad wear,
check the wear indicator grooves. If a brake
pad has worn to the point that the wear indi-
cator grooves have almost disappeared, have
a Yamaha dealer replace the brake pads as a
set.
The wheels need to be removed to check the
brake pads. (See pages 8-40, 8-42 for wheel
removal and installation procedures.)

UB427BE0.book  Page 33  Friday, February 5, 2016  2:14 PM

Содержание Viking YXM70VPHH 2016













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды