Yamaha VF200 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 120

Yamaha VF200 Скачать руководство пользователя страница 79

Maintenance

73

2. Drain the cooling water completely out of

the outboard motor. Clean the body thor-
oughly.

EMU41072

Lubrication

1. Change the gear oil. For instructions,

see page 92. Check the gear oil for the
presence of water that indicates a leaky
seal. Seal replacement should be per-
formed by an authorized Yamaha dealer
prior to use.

2. Lubricate all grease fittings. For further

details, see page 79.

TIP:

For long-term storage, fogging the engine
with fogging oil is recommended. Contact
your Yamaha dealer for information about
fogging oil and procedures for your outboard
motor.

EMU41154

Cleaning and anticorrosion
measures

1. Wash the exterior of the outboard motor

using fresh water, and then dry the out-
board motor completely. For instructions
on cleaning the outboard motor, see
page 72.

NOTICE:

Do not spray water

into the air intake.

[ECM01841]

2. Spray the outboard motor powerhead

with “Yamaha Silicone Protectant.”

3. Wax the cowling with a non-abrasive

wax such as “Yamalube Professional
Polish.”

EMU40964

Flushing cooling water passage

Perform this procedure right after operation
for the most thorough flushing.

NOTICE

ECM01531

Do not perform this procedure while the
engine is running. The water pump may
be damaged and severe damage from
overheating can result.

1. Disconnect the garden hose connector

from the fitting on the bottom cowling.

2. Connect the garden hose to the garden

1. Air intake

1

ZMU06944

1. Fitting
2. Garden hose connector
3. Garden hose adapter

1

2

3

ZMU08065

6CB-9-3B-1E0.book 73 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
77
78
79
80
81
...
»

Содержание VF200

























































































































Отзывы:

Нет отзывов