manualshive.com logo in svg

Yamaha VF200, Руководство пользователя, Страница: 20 / 120

Поделиться
Скачать
Yamaha VF200 Скачать руководство пользователя страница 20

14

Specifications and requirements

EMU40501

Specifications

TIP:

“(SUS)” indicates that the specification is for
the outboard motor when it is equipped with
a stainless steel propeller.

EMU2821V

Dimension and weight:

Overall length:

959 mm (37.8 in)

Overall width:

664 mm (26.1 in)

Overall height L:

1749 mm (68.9 in) (VF200A, 
VF225A, VF250A)

Overall height X:

1893 mm (74.5 in) (VF250A)

Motor transom height L:

493 mm (19.4 in) (VF200A, VF225A, 
VF250A)

Motor transom height X:

643 mm (25.3 in) (VF250A)

Dry weight (SUS) L:

239 kg (527 lb) (VF200A, VF225A, 
VF250A)

Dry weight (SUS) X:

259 kg (571 lb) (VF250A)

Performance:

Full throttle operating range:

5000–6000 r/min

Rated power:

147.1 kW (200 HP) (VF200A)
165.5 kW (225 HP) (VF225A)
183.8 kW (250 HP) (VF250A)

Idle speed (in neutral):

650–750 r/min (VF250XA)
700–800 r/min (VF200A, VF225A, 
VF250LA)

Power unit:

Type:

4-stroke DOHC V6 24 valves

Total displacement:

4169 cm

3

 (254.4 c.i.)

Bore 

 stroke:

96.0 

 96.0 mm (3.78 

 3.78 in)

Ignition system:

TCI

Spark plug (NGK):

LFR6A-11

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Steering system:

Remote steering

Starting system:

Electric starter

Starting carburetion system:

Fuel injection

Valve clearance IN (cold engine):

0.17–0.24 mm (0.0067–0.0094 in)

Valve clearance EX (cold engine):

0.31–0.38 mm (0.0122–0.0150 in)

Battery rating (CCA/SAE):

680–1150 A

Battery rating (MCA/ABYC):

770–1370 A

Battery rating (RC/SAE):

160 minutes

Battery rating (CCA/EN):

640–1080 A

Battery rating (20HR/IEC):

80 Ah

Maximum generator output:

50 A

Lower unit:

Gear shift positions:

Forward-neutral-reverse

Gear ratio:

1.75 (21/12)

6CB-9-3B-1E0.book  14 ページ  ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Отзывы:

Нет отзывов