manualshive.com logo in svg

Yamaha V150, Руководство пользователя

Поделиться
Скачать
Yamaha V150 Скачать руководство пользователя страница 61

 

Maintenance

 

56

 

Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-

 

er unit.

 

EMU29320

 

Checking battery (for electric start 
models)

WARNING

 

EWM00330 

 

Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is
poisonous and highly caustic.
Always follow these preventive mea-
sures:

 

●

 

Avoid bodily contact with electrolytic
fluid as it can cause severe burns or
permanent eye injury.

 

●

 

Wear protective eye gear when han-

dling or working near batteries.

Antidote (EXTERNAL):

 

●

 

SKIN - Flush with water.

 

●

 

EYES - Flush with water for 15 minutes
and get immediate medical attention.

Antidote (INTERNAL):

 

●

 

Drink large quantities of water or milk
followed by milk of magnesia, beaten
egg, or vegetable oil. Get immediate
medical attention.

Batteries also generate explosive hydro-
gen gas; therefore, you should always
follow these preventive measures:

 

●

 

Charge batteries in a well-ventilated ar-
ea.

 

●

 

Keep batteries away from fire, sparks,
or open flames (for example: welding
equipment, lighted cigarettes, and so
on.)

 

●

 

DO NOT SMOKE when charging or han-
dling batteries.

KEEP BATTERIES AND ELECTROLYTIC

 

FLUID OUT OF REACH OF CHILDREN.

CAUTION:

 

ECM00360 

 

●

 

A poorly maintained battery will quickly
deteriorate.

 

●

 

Ordinary tap water contains minerals
harmful to a battery, and should not be

 

used for topping up.

 

1.

Check the electrolyte level at least once
a month. Fill to the manufacturer’s rec-
ommended level when necessary. Top
up only with distilled water (or pure de-
ionized water suitable to use in batter-
ies).

ZMU01901

ZMU03461

Содержание V150



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды