manualshive.com logo in svg

Yamaha V150, Руководство пользователя

Поделиться
Скачать
Yamaha V150 Скачать руководство пользователя страница 60

 

Maintenance

 

55

 

oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the
gear case.

3.

Remove the gear oil drain screw and
gasket.

NOTE:

 

●

 

If a magnetic gear oil drain screw is
equipped, remove all metal particles from
the screw before installing it.

 

●

 

Always use new gaskets. Do not reuse the

 

removed gaskets.

4.

Remove the oil level plug and gasket to
allow the oil to drain completely.

CAUTION:

 

ECM00710 

 

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-

 

pair of the lower unit seals.

NOTE:

 

For disposal of used oil, consult your

 

Yamaha dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-

ized filling device, inject the gear oil into
the gear oil drain screw hole.

6.

Put a new gasket on the oil level plug.
When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

7.

Put a new gasket on the gear oil drain
screw. Insert and tighten the gear oil
drain screw.

 

EMU29312

 

Inspecting and replacing anode(s)

 

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

CAUTION:

 

ECM00720 

 

Do not paint anodes, as this would render

 

them ineffective.

NOTE:

 

Inspect ground leads attached to external
anodes on equipped models. Consult a

 

1. Gear oil drain screw
2. Oil level plug

1

2

ZMU01899

 

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

980.0 cm

 

3

 

 (33.13 US oz) (34.56 

Imp.oz)

ZMU01900

Содержание V150



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды