PERIODIC MAINTENANCE
3-9
• Turn the crankshaft counterclockwise several
full turns to seat the parts.
h. Measure the valve clearance again.
i. If the valve clearance is still out of specifi-
cation, repeat all of the valve clearance
adjustment steps until the specified clear-
ance is obtained.
8. Install:
• All removed parts
TIP
For installation, reverse the removal procedure.
EAS31017
CHECKING THE ENGINE IDLING SPEED
TIP
Prior to checking the engine idling speed, the
throttle body synchronization should be adjusted
properly, the air filter element should be clean,
and the engine should have adequate compres-
sion.
1. Start the engine and let it warm up for several
minutes.
2. Check:
• Engine idling speed
Out of specification
→
Go to next step.
3. Check:
• ISC (idle speed control) learning value
“00” or “01”
→
Check the intake system.
“02”
→
Clean the ISC (idle speed control)
valve.
Refer to “CHECKING AND CLEANING THE
THROTTLE BODIES” on page 7-8.
a. Connect the Yamaha diagnostic tool.
Use the diagnostic code number “67”.
Refer to “SELF-DIAGNOSTIC FUNC-
TION AND DIAGNOSTIC CODE TABLE”
on page 9-1.
b. Check the ISC (idle speed control) leaning
value.
EAS30797
SYNCHRONIZING THE THROTTLE BODIES
TIP
Before synchronizing the throttle bodies, check
the following items:
• Valve clearance
• Spark plugs
• Air filter element
• Throttle body joints
• Fuel hose
• Exhaust system
• Cylinder head breather hose
• Vacuum hoses
Checking the throttle body synchronization
1. Stand the vehicle on a level surface.
TIP
Place the vehicle on a suitable stand.
2. Remove:
• Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.
• Air scoops
• Air ducts
• Fuel tank side cover
Refer to “GENERAL CHASSIS (3)” on page
4-5.
• Fuel tank
Refer to “FUEL TANK” on page 7-1.
3. Disconnect:
• Intake air pressure sensor hose
• Cap
Refer to “THROTTLE BODIES” on page 7-5.
4. Install:
• Hose “1” (Parts No.: 5JW-24311-00)
• 3-way joint “2” (Parts No.: 90413-05014)
• Vacuum gauge hose #1 “3” (to throttle body
#1)
• Vacuum gauge hose #2 “4” (to throttle body
#2)
• Intake air pressure sensor hose “5”
• Vacuum gauge “6”
Engine idling speed
1250–1450 r/min
Yamaha diagnostic tool USB
90890-03267
Yamaha diagnostic tool (A/I)
90890-03262
Vacuum gauge
90890-03094
Vacuummate
YU-44456
Содержание Tenere 700 2020
