Yamaha Star XV19MY Скачать руководство пользователя | Manualshive

Страница: 71 / 94

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-29

7

EAU38382

Replacing a turn signal light
bulb

1. Remove the turn signal light lens

by removing the screw, and then
turning the lens counterclockwise.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by turning it clock-

wise, and then installing the screw.

NOTICE:

Do not overtighten the

screw, otherwise the lens may
break.

[ECA11191]

EAU24330

License plate light

If the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.

EAU24350

Supporting the motorcycle

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

1. Screw

U1D713E0.book Page 29 Thursday, May 8, 2008 4:19 PM

«
...
69
70
71
72
73
...
»

Содержание Star XV19MY































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19MY

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 288

TRACER 700 2020

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 118

XV1700PCR Road Star Warrior

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 429

Бренд: Yamaha Страницы: 427

Moto matrix YZF-R6S

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 662

Бренд: R&G Страницы: 14

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Бренд: Termignoni Страницы: 9

SPORTCITY CUBE 125

Бренд: APRILIA Страницы: 157

2016 Empulse TT

Бренд: Victory Motorcycles Страницы: 138

Бренд: Suzuki Страницы: 42

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды