Yamaha Star XV19MY Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 94

background image

OPERATION AND IMPORTANT RIDING POINTS

6-3

6

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

TIP

When shifting gears in normal operat-
ing conditions, use the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (16 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16720

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17112

0–1000 km (0–600 mi)

Avoid prolonged operation above 2500
r/min.

NOTICE:

After 1000 km (600

mi) of operation, the engine oil and
transfer case oil must be changed,
and the oil filter cartridge or element
replaced.

[ECA10892]

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 3500
r/min.

Shift up points:

1st

→

2nd: 20 km/h (13 mi/h)

2nd

→

3rd: 30 km/h (19 mi/h)

3rd

→

4th: 40 km/h (25 mi/h)

4th

→

5th: 50 km/h (31 mi/h)

Shift down points:

5th

→

4th: 25 km/h (16 mi/h)

4th

→

3rd: 25 km/h (16 mi/h)

3rd

→

2nd: 25 km/h (16 mi/h)

2nd

→

1st: 25 km/h (16 mi/h)

U1D713E0.book Page 3 Thursday, May 8, 2008 4:19 PM

«
...
39
40
41
42
43
...
»

Содержание Star XV19MY































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19MY

Бренд: LAZER Страницы: 13

Бренд: Baja motorsports Страницы: 8

Бренд: Yukon Trail Страницы: 24

Бренд: Yamaha Страницы: 287

Бренд: DAELIM Страницы: 68

Бренд: Saddlemen Страницы: 3

Бренд: KSR Moto Страницы: 51

Battery Relocation Kit

Бренд: BoxerCafe Страницы: 7

MASTERFOX 125cc 2015

Бренд: d'Magna Страницы: 29

Бренд: hepco & becker Страницы: 5

Бренд: PUIG Страницы: 2

Бренд: Yamaha Страницы: 94

Star XVS13CG 2015

Бренд: Yamaha Страницы: 98

Star XV250G 2015

Бренд: Yamaha Страницы: 88

Star XVS13CTD 2012

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 104

Star XV250H 2016

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды