Yamaha Star XV19MY Скачать руководство пользователя

Страница: 33 / 94

INSTRUMENT AND CONTROL FUNCTIONS

4-17

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU44891

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

U1D713E0.book Page 17 Monday, June 23, 2008 2:53 PM

Содержание Star XV19MY































































































Результаты поиска

Содержание Star XV19MY

Отзывы:

Похожие инструкции для Star XV19MY

Бренды по названию

Популярные бренды

Yamaha Star XV19MY, Руководство пользователя

Результаты поиска

Содержание Star XV19MY

Отзывы:

Похожие инструкции для Star XV19MY

Бренды по названию

Популярные бренды