Yamaha Star XV19MY Скачать руководство пользователя

Страница: 26 / 94

INSTRUMENT AND CONTROL FUNCTIONS

4-10

EAU12890

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13121

Fuel tank cap

To remove the fuel tank cap

Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released
and the fuel tank cap can be removed.

To install the fuel tank cap

1. Insert the fuel tank cap into the

tank opening with the key inserted
in the lock and with the “

” mark

facing forward.

1. Brake lever

1. Brake pedal

1. Fuel tank cap lock cover

2. “

” mark

3. Unlock.
4. Lock.

U1D713E0.book Page 10 Thursday, May 8, 2008 4:19 PM

Содержание Star XV19MY































































































Результаты поиска

Содержание Star XV19MY

Отзывы:

Похожие инструкции для Star XV19MY

Бренды по названию

Популярные бренды

Yamaha Star XV19MY, Руководство пользователя

Результаты поиска

Содержание Star XV19MY

Отзывы:

Похожие инструкции для Star XV19MY

Бренды по названию

Популярные бренды