Yamaha Star XV19CTSZ 2009 Скачать руководство пользователя | Manualshive

Страница: 67 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

7

EAU38630

Checking the brake and clutch
fluid levels

Front brake

Rear brake

Clutch

Insufficient brake or clutch fluid may al-
low air to enter the brake or clutch sys-
tems, possibly causing them to become
ineffective.

TIP

The rear brake fluid reservoir is located
under the rider seat. (See page 4-14.)

Before riding, check that the brake and
clutch fluids are above the minimum
level marks and replenish if necessary.
A low brake or clutch fluid level may in-
dicate brake or clutch system leakage
and/or worn brake pads. If the brake or
clutch levels are low, be sure to check
the brake or clutch systems for leakage
and the brake pads for wear.

Observe these precautions:

●

When checking the brake and
clutch fluid levels, make sure that
the top of each reservoir is level.

●

Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking or clutch
performance.

●

Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking or clutch per-
formance.

●

Be careful that water does not en-
ter the brake or clutch fluid reser-
voir when refilling. Water will
significantly lower the boiling point
of the fluid and may result in vapor
lock.

●

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

1. Minimum level mark

1. Minimum level mark

1. Minimum level mark

Recommended brake and clutch flu-
id:

DOT 4 brake fluid

U2C514E0.book Page 19 Tuesday, September 8, 2009 10:12 AM

«
...
65
66
67
68
69
...
»

Содержание Star XV19CTSZ 2009









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19CTSZ 2009

Бренд: Suzuki Страницы: 230

Бренд: hepco & becker Страницы: 5

MILWAUKEE-EIGHT 5833

Бренд: JIMS Страницы: 10

fire PANTLINER AJ6

Бренд: ALPENHEAT Страницы: 26

Daytona 955i 2002

Бренд: Triumph Страницы: 384

Бренд: Mallory Страницы: 3

Бренд: Honda Страницы: 362

Бренд: KTM Страницы: 207

Бренд: LSL Страницы: 4

BRUTALE 750 ORO

Бренд: MV Agusta Страницы: 386

Бренд: Kenwood Страницы: 36

Бренд: Kenwood Страницы: 97

Бренд: IBEX Страницы: 3

Бренд: SANYANG INDUSTRY CO. Страницы: 122

Бренд: N-Com Страницы: 36

Бренд: Bell Sports Страницы: 20

Бренд: KTM Страницы: 12

Бренд: KTM Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды