Yamaha Star XV19CTSZ 2009 страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-16

7

WARNING

EWA10580

●

It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

●

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

Tire information

This motorcycle is equipped with cast
wheels and tubeless tires.

WARNING

EWA10461

The front and rear tires should be of
the same make and design, other-
wise the handling characteristics of
the vehicle may be different, which
could lead to an accident.

After extensive tests, only the tires list-
ed below have been approved for this
model by Yamaha Motor Co., Ltd.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

Front tire:

Size:

130/70R18M/C 63H

Manufacturer/model:

DUNLOP/D251F
BRIDGESTONE/G851 RADIAL G

Rear tire:

Size:

190/60R17M/C 78H

Manufacturer/model:

DUNLOP/D251
BRIDGESTONE/G850 RADIAL G

U2C514E0.book Page 16 Tuesday, September 8, 2009 10:12 AM

«
...
62
63
64
65
66
...
»

Содержание Star XV19CTSZ 2009









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19CTSZ 2009

Бренд: LAZER Страницы: 13

Бренд: HYOSUNG Страницы: 199

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренд: Cobra Страницы: 38

Бренд: KTM Страницы: 21

Бренд: Yamaha Страницы: 390

Бренд: Yamaha Страницы: 468

Бренд: Yamaha Страницы: 364

Бренд: HJC Страницы: 7

Бренд: VESPA Страницы: 46

ETV mille Caponord

Бренд: APRILIA Страницы: 384

Бренд: Honda Страницы: 143

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 2

Бренд: KTM Страницы: 7

Бренд: Indian Motorcycle Страницы: 7

Бренд: Honda Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды