Yamaha Star XV19CTSZ 2009 страница 58 Скачать руководство пользователя | Manualshive

Страница: 58 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-10

7

EAU19681

Canister (for California only)

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

●

Check each hose connection.

●

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

●

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

EAU3836A

Engine oil and oil filter car-
tridge

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.

2. Remove the rider seat. (See page

3. Start the engine, warm it up until

the engine oil has reached a nor-
mal temperature of 60 °C (140 °F),
let it continue to idle for ten sec-
onds, and then turn the engine off.

TIP

To achieve the proper engine oil tem-
perature for an accurate oil level read-
ing, the engine must have first

completely cooled down, and then
warmed up again for several minutes to
normal operating temperature.

4. Wait a few minutes until the oil set-

tles, remove the oil filler cap, wipe
the engine oil dipstick clean, insert
it back into the oil filler hole (with-
out screwing it in), and then re-
move it again to check the oil level.

TIP

The engine oil should be between the
minimum and maximum level marks.

1. Engine oil filler cap

U2C514E0.book Page 10 Tuesday, September 8, 2009 10:12 AM

«
...
56
57
58
59
60
...
»

Содержание Star XV19CTSZ 2009









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19CTSZ 2009

Бренд: N-Com Страницы: 6

Бренд: Cobra Страницы: 38

Бренд: KSR Moto Страницы: 51

Бренд: Pandora Страницы: 56

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: Sinnis motorcycles Страницы: 68

Бренд: Thunderbike Страницы: 7

TRACER MTT9K 2019

Бренд: Yamaha Страницы: 122

TT-R125(N) 2000

Бренд: Yamaha Страницы: 508

TT-R125(R) 2002

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 610

TT-R125(S) 2003

Бренд: Yamaha Страницы: 610

Бренд: Yamaha Страницы: 616

Бренд: Yamaha Страницы: 90

Бренд: LAS Страницы: 22

Бренд: DYNATEK Страницы: 4

BAR CLAMP MOUNT PRO

Бренд: SP CONNECT Страницы: 3

Бренд: R&G Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды