Yamaha Star XV19CTSZ 2009 Скачать руководство пользователя | Manualshive

Страница: 38 / 104

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-22

4

EAU15282

EXUP system

This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve)
system. This system boosts engine
power by means of a valve that regu-
lates the inner diameter of the exhaust
pipe. The EXUP system valve is con-
stantly adjusted in accordance with the
engine speed by a computer-controlled
servomotor.

NOTICE

ECA10191

●

The EXUP system has been set
and extensively tested at the
Yamaha factory. Changing
these settings without sufficient
technical knowledge may result
in poor performance of or dam-
age to the engine.

●

If the EXUP system cannot be
heard when the main switch is
turned on, have a Yamaha deal-
er check it.

EAU15303

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

TIP

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See page 4-23 for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

U2C514E0.book Page 22 Tuesday, September 8, 2009 10:12 AM

«
...
36
37
38
39
40
...
»

Содержание Star XV19CTSZ 2009









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19CTSZ 2009

Бренд: Baja motorsports Страницы: 20

Бренд: Memphis Shades Страницы: 2

Daytona Moto2 765 2020

Бренд: Triumph Страницы: 163

Бренд: KYMCO Страницы: 424

Бренд: Honda Страницы: 91

Bonneville T100

Бренд: Triumph Страницы: 198

Бренд: Suzuki Страницы: 42

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 304

Sport 1 180 - 487.3

Бренд: CZ Страницы: 42

Бренд: SAFARI Страницы: 18

Бренд: Sealey Страницы: 2

X-Small Dry Duffel Bag

Бренд: Tusk Страницы: 3

Бренд: Benelli Страницы: 408

Бренд: Beta Страницы: 38

Бренд: Beta Страницы: 60

Бренд: Beta Страницы: 68

Бренд: Beta Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды