Yamaha STAR XV19CSX Скачать руководство пользователя | Manualshive

Страница: 54 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-13

6

EAU36762

Air filter element

The air filter element must be replaced
at the intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer replace the air
filter element.

EAU21382

Checking the throttle cable
free play

The throttle cable free play should mea-
sure 4.0–6.0 mm (0.16–0.24 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

EAU21401

Valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

1. Throttle cable free play

U29S10E0.book Page 13 Friday, May 18, 2007 1:53 PM

«
...
52
53
54
55
56
...
»

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Похожие инструкции для STAR XV19CSX

Бренд: Parkside Страницы: 89

Бренд: Parkside Страницы: 28

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: Memphis Shades Страницы: 2

Бренд: Sena Страницы: 25

Бренд: Two Brothers Racing Страницы: 2

WOLVERINE R MAX 2021

Бренд: Yamaha Страницы: 190

Бренд: Yamaha Страницы: 194

WOLVERINE RMAX2 2024

Бренд: Yamaha Страницы: 196

Vstar XVS650T 2004

Бренд: Yamaha Страницы: 101

Бренд: hepco & becker Страницы: 3

Бренд: Chicago Electric Страницы: 7

Бренд: Chicago Electric Страницы: 10

Бренд: Ermax Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: APRILIA Страницы: 96

Бренд: Honda Страницы: 168

Бренд: Gmax Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды