Yamaha STAR XV19CSX Скачать руководство пользователя | Manualshive

Страница: 32 / 96

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-15

3

EAU15301

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

NOTE:

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU15312

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10250

If a malfunction is noted, have a
Yamaha dealer check the system be-
fore riding.

U29S10E0.book Page 15 Friday, May 18, 2007 1:53 PM

«
...
30
31
32
33
34
...
»

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Похожие инструкции для STAR XV19CSX

Бренд: Dakota Digital Страницы: 6

Бренд: Spartus Страницы: 24

Бренд: Crivit Страницы: 50

Бренд: Triumph Страницы: 53

Бренд: KTM Страницы: 21

Бренд: Pacific Helmets Страницы: 40

Бренд: Malossi Страницы: 24

Бренд: Honda Страницы: 130

Бренд: hepco & becker Страницы: 3

Бренд: DYNATEK Страницы: 4

1003007FONTANASPRINT

Бренд: DYNATEK Страницы: 7

Бренд: Yamasaki Страницы: 28

Бренд: RIEJU Страницы: 39

Бренд: RIEJU Страницы: 51

Бренд: Vetter Страницы: 18

Бренд: X-lite Страницы: 57

FreeGo LTK125 2019

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды